AMB25 (RTL8720DF) Supported ARDUINO built-in example table

There are many built-in examples in Arduino. In the table below, we list all examples that are compatible with Ameba.
Please refer the following link to set up Ameba for Arduino IDE.
Refer the following link for Arduino built-in example details.

Category	Name	Comment	Remarks
01. Basics	AnalogReadSerial	Connect potentiometer to 3.3V. ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset).	ADC pin options A4 (PB1), A5 (PB2), A6 (PB3). ADC pin reading voltage range 0 to 3.3V. ADC value can be calibrated by modifying _offset and _gain using 2 points calibration method. analogSet(float gain, float offset) can be used to update the calibrated offset and gain values.
	BareMinimum
	Blink	LED_BUILTIN sets to any GPIO pins.
	DigitalReadSerial
	Fade	For "analogWrite()", use PWM capable pin.	PWM capable Pin 2, 3, 4, 5, 6, 7, 14, 15, 16, 17, 18, and 19.
	ReadAnalogVoltage	ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset).
02. Digital	BlinkWithoutDelay	LED_BUILTIN sets to any GPIO pins.
	Button
	Debounce
	DigitalInputPullup
	StateChangeDetection
	toneKeyboard	ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). For "analogRead()", use ADC pin name (A4 to A6) instead the integer number. For "tone()" and "noTone()", use PWM capable pin.
	toneMelody
	toneMultiple
	tonePitchFollower
03. Analog	AnalogInOutSerial	ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). For "analogWrite()", use PWM capable pin.
	AnalogInput
	AnalogWriteMega
	Calibration
	Fading
	Smoothing
04. Communication	ASCIITable
	Dimmer	For "analogWrite()", use PWM capable pin.
	Graph	Connect potentiometer to 3.3V. ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset).
	Midi	Use Serial1, MIDI jack pin 5 connected to SERIAL1_TX; Use Serial2, MIDI jack pin 5 connected to SERIAL2_TX.
	MultiSerial
	PhysicalPixel
	SerialCallResponse	ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). For "analogRead()", use ADC pin name (A4 to A6) instead the integer number.
	ReadASCIIString	For "analogWrite()", use PWM capable pin.
	SerialEvent
	SerialPassthrough		Serial options, Serial, Serial1 or Serial2.
	VirtualColorMixer	ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset).
05. Control	Arrays	ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). For "analogWrite()", use PWM capable pin.
	ForLoopIteration
	IfStatementConditional
	switchCase
	switchCase2
	WhileStatementConditional
06. Display	barGraph	ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset).
	RowColumnScanning	ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). In line 41, replace, pin 11 and pin 10 with pin 1 and pin 0 respectively. For “analogRead()”, use A4 and A5 instead of A0 and A1. After line 101, add delay(1);
07. Strings	CharacterAnalysis
	StringAdditionOperator
	StringAppendOperator
	StringCaseChanges
	StringCharacters
	StringComparisonOperators	ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset).
	StringIndexOf
	StringLength
	StringLengthTrim
	StringReplace
	StringStartsWithEndsWith
	StringSubstring
	StringToInt