BW16 (RTL8720DN) 与 Ameba 相容的 ARDUINO 范例表
| Category | Name | Comment | Remarks |
| 01. Basics | AnalogReadSerial | Connect potentiometer to 3.3V. ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). | ADC pin options A2 (PB3). ADC pin reading voltage range 0 to 3.3V. ADC value can be calibrated by modifying _offset and _gain using 2 points calibration method. analogSet(float gain, float offset) can be used to update the calibrated offset and gain values. |
| BareMinimum | |||
| Blink | LED_BUILTIN sets to LED_G (on-board LED blue) | LED options, on-board LED, LED_R (red), LED_B (blue), or LED_G (green). LED_B and LED_G are PWM capable LED. | |
| DigitalReadSerial | |||
| Fade | For “analogWrite()”, use PWM capable pin. | PWM capable Pin 3, 7, 8, 11, and 12. | |
| ReadAnalogVoltage | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). | ||
| 02. Digital | BlinkWithoutDelay | LED_BUILTIN sets to LED_B (on-board LED blue) | LED options, on-board LED. |
| Button | Replace any Pin that sets beyond Pin 0 to 12. | ||
| Debounce | |||
| DigitalInputPullup | |||
| StateChangeDetection | |||
| toneKeyboard | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). For “analogRead()”, use ADC pin name (A2) instead the integer number. For “tone()” and “noTone()”, use PWM capable pin. | ||
| toneMelody | |||
| toneMultiple | |||
| tonePitchFollower | |||
| 03. Analog | AnalogInOutSerial | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). For “analogWrite()”, use PWM capable pin. Replace any Pin that sets beyond Pin 0 to 12. | LED options, on-board LED. LED_B and LED_G are PWM capable LED. |
| AnalogInput | |||
| AnalogWriteMega | |||
| Calibration | |||
| Fading | |||
| Smoothing | |||
| 04. Communication | ASCIITable | LED options, on-board LED. LED_B and LED_G are PWM capable LED. | |
| Dimmer | For “analogWrite()”, use PWM capable pin. | ||
| Graph | Connect potentiometer to 3.3V. ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). | ||
| Midi | Use Serial1, MIDI jack pin 5 connected to SERIAL1_TX. | ||
| MultiSerial | Required external USB-to-UART module. | ||
| PhysicalPixel | Replace any Pin that sets beyond Pin 0 to 12. | ||
| ReadASCIIString | For “analogWrite()”, use PWM capable pin. | ||
| SerialEvent | |||
| SerialPassthrough | Required external USB-to-UART module. | ||
| 05. Control | Arrays | ||
| ForLoopIteration | |||
| IfStatementConditional | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). Replace any Pin that sets beyond Pin 0 to 12. | LED options, on-board LED. | |
| switchCase | ADC pin used, up to 3.3V. | ||
| switchCase2 | |||
| WhileStatementConditional | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). For “analogWrite()”, use PWM capable pin. Replace any Pin that sets beyond Pin 0 to 12. | LED options, on-board LED. LED_B and LED_G are PWM capable LED. | |
| 06. Display | barGraph | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). | |
| 07. Strings | CharacterAnalysis | ||
| StringAdditionOperator | |||
| StringAppendOperator | |||
| StringCaseChanges | |||
| StringCharacters | |||
| StringComparisonOperators | ADC pin used, up to 3.3V and can be calibrated by using analogSet(float gain, float offset). | ||
| StringIndexOf | |||
| StringLength | |||
| StringLengthTrim | |||
| StringReplace | |||
| StringStartsWithEndsWith | |||
| StringSubstring | |||
| StringToInt |
Copyrights ©瑞晟微电子(苏州)有限公司 2021. All rights reserved. 使用条款
